Ozone Analyzers and Monitors

The model UV-100 ozone analyzer is for general purpose measurement of ozone in air. Its range is .01-900 ppm (v) with 2% accuracy, and it includes a built-in data logger. The UV-100 weighs only 2.1 kg (4.7 lb), it is powered by an AC adapter or 12 V external battery, and is equally versatile for the laboratory or for process monitoring. The outputs are digital display, 0-2.5 VDC and 4-20 mA. The instrument featurs LEDs to indicate calibration is due, the sample line filter should be replaced, and that the sampling area is above the danger limit of .1 ppm.

Using proprietary technology, our instrument strips the ozone from the water stream and reads it as the concentration of ozone released into a measuring chamber. This has advantages over conventional methods for measuring dissolved ozone.

Typical applications:

• Bottled water plants
• Food treatment systems
• Equipment sterilizing systems
• Wastewater treatment monitoring
• Factory pure water process and control

Features:

• Specific to ozone
• Insensitive to most interfering chemicals such as salt and chlorine
• Low cost and easily replaceable parts
• User can easily calibrate the instrument to any in-house standard
• Set-point relay for alarm or system control
• 4-20 mA output to PLC or other remote readouts and controllers

Requirements:

• Water feed at > 14 psi (1 bar)
• .15 liters/minute (3 gallons/hour) flow to drain or reclaim
• 12 VDC 800 mA power supply

A general purpose sensor and monitor. Designed for rugged indoor field use, factories, pilot plants, process facilities, and sensor and monitoring uses of all kinds. Uses the same precalibrated sensor modules as our OS-4 permanent monitor and controller. All digital technology.

• Autoranging .030-1.999 ppm and 2.0-20.00 ppm.
• 10% accuracy. T and RH compensated.
• 12 hour (est) battery life. 8 hour charge. 4 hour fast charge available.
• Plug-in precalibrated sensor modules.
• Internal data logger with instant readout of high, low and average of data.
• Data port for external data logger such as our DL-3.
• USB, 4-20 mA, 0-2 VDC outputs for loggers, computers and PLC.
• Tilt stand and wall hanging hook.
• Back light for LCD display.
• Improved HMOS heated metal oxide sensor.
• Size 108 W × 222 L × 64 D mm .71 kg.
  4¼ W × 8¾ L × 2½ D in 1lb 10 oz.
• Power source: Internal rechargeable batteries or 12-24 VDC, 500 mA, from external adapter/charger.

Features:

• 0.02 - 2.00 ppm
• 20% accuracy
• Less than one minute response time
• 8 hour TWA. Data logger optional
• Audio, LED and vibration alarms
• Also available for CO and H2S

Features:

• 0.00 - 5.00 ppm
• 20% accuracy
• 1 minute response time
• No test chemicals or disposables
• Hand-held and easy to use

The Model A-21ZX portable ozone sensor provides a reliable and inexpensive way of checking generators, valves, piping and general environments for ozone leaks and for estimating ozone levels. It can be used as a permanent monitor indoors when concentrations average below .1 ppm. It may be used outdoors for ozone studies in moderate temperature conditions.

Features:

• Small size and high sensitivity
• Ease of calibration and service
• Instant On
• Very simple operation

The C-30ZX Ozone Monitor provides a reliable and inexpensive way of continuous monitoring for low levels of OZONE gas for water treatment plants, pulp bleaching mills, photocopier and laser printer centers, fumigation projects, indoor air quality systems, and wherever ozone exposure is possible. The C-30ZX has a very fast and continuous response, constantly monitoring your work environment.

Benefits:

• Constantly monitors your work environment; shows the ozone concentration by a multicolor graphical display, and alarms when there is a health hazard
• No installation typically required; easily understood by non-technical personnel
• Virtually no maintenance

Features:

• LED readout changes color as ozone level increases
• Audio alarm and output for data logger
• Connections for external equipment control
• For general monitoring and ozone control
• Many accessories available such as data loggers, calibrators, and protective enclosures with heaters and 4-20 mA outputs

For monitoring ozone levels near small ozone generators. Ideal for light commercial applications such as bars and restaurants, hotels, photocopy centers, water bottlers, fumigation, research projects, light manufacturing, swimming pools, residential and wherever ozone exposure is possible. For permanent on-site use and for portable work by field engineers and installers.

The EZ-1 has a fast and continuous response. It is rugged and versatile. There are no touchy controls

Features:

• Constantly monitors your work environment. Ozone concentration shown by a multicolored graphical display from green (safe) to yellow (caution) to red (danger).
• No installation required. Easily understood by non-technical personnel.
• Field work and walk around analyses possible via power from internal rechargeable batteries.
• Compatible with other Eco Sensors VOC and ozone sensing, monitoring, and control products.
• Lowest cost.

For checking residual dissolved ozone levels in bottled water, swimming pools, spas, water treatment systems, aquariums, food washing and canning, wineries, agriculture, cooling towers, research projects, and much more.

Equally useful in the Plant, lab or field.

Uses 50 ml samples. The sensor does not contact the water. There are no interferences from Chlorine or Salinity

Features:

• No fouling of the sensor. No special probe installation. No sensor-water contact.
• Easily understood by non-technical personnel. No confusing chemistries or restrictions.
• Easy to check calibration by standard kits and by Eco Sensors ozone sources.
• Can use AC power via low voltage adapter or can use internal rechargeable batteries.
• Lowest cost. No consumables.

The OG-3 ozone source calibrator is for calibration verification and simple approximate calibration of Eco Sensors ozone instruments.

It is available in either of two outputs: .1 ppm or 1 ppm. The OG-3 is powered by an AC adapter supplying 12 VDC.

The OG-3 uses a precision quartz UV lamp ozone generator. Its output is adjusted in our laboratory by comparison with a NIST traceable standard.

• Acts like a thermostat to control ozone generators and alarms based on an adjustable ozone concentration set-points.
• Ozone ppm readout via digital meter.
• Simple and inexpensive.

Acts like a thermostat to control ozone generators and alarms based on an adjustable ozone concentration set-points. Ozone ppm readout via digital meter. Simple and inexpensive.

FEATURES

• Easy to install. Minimal adjustments.
• Sensor is in a replaceable precalibrated module.
• Separated by a 42-inch. cable, the instrument is not in the high ozone area.
• Operates from 12-24 volts DC or from AC adapters available worldwide.
• Programmable turn-on and turn-off set-points.
• Indication when .1 ppm safety standard exceeded.

The RAP-2 Remote Alarm Panel is for alarming when signals from ozone and VOC monitors reach preset limits or set points. The alarms are a red strobe light and a loud audible alarm (90 dB at 3 meters). There is also a digital readout in PPM of ozone. The RAP-2 also outputs its input signal in 4.20 mA form for building automation systems and other applications requiring long signal paths. The RAP-2 is powered by 14-30 VAC or DC. This remote alarm panel is usually used with the C-30Z, C-30ZX, EE-1, EE-2, OS-3 and 0S-4. It can be used with some other instruments by special order.

Typical Applications:

• Swimming pools.
• Laundries using ozone.
• Large noisy factory environments.
• Casinos and other ozonated public areas.
• Agricultural storage areas.
• Farms.
• Food processing plants.

Features:

• Rugged polycarbonate enclosure with hinged door.
• Accepts input of 0-2 VDC, 4-20 mA and relay closure.
• Loud pulsating audio alarm with silencing button.
• Very bright red strobe light.
• 4-20 mA signal and relay outputs.
• Alarm set-point adjustment.
• Uses easily available 14-30 VAC or DC power.
• Signals from instruments can be transmitted by inexpensive twisted pair.
• 125 × 175 × 77 mm (5 × 7 × 3 in).

Includes Audio Alarm, Battery operation and Provision for External Alarm and Data Logger

For paint shops, printers, dry cleaners, woodworkers, vehicle repair facilities, chemical production areas and wherever indoor air quality monitoring is required: the Model C-21 gas sensor helps you comply with the new VOC air quality regulations for hydrocarbon gases and solvent vapors.

Benefits:

• Constantly monitors your work environment. Detects leaks and poor air quality before they are a health hazard. Alarms below OSHA TLV for most common solvent-based VOCs.
• No installation. Easily used and understood by non-technical personnel.
• Virtually no maintenance.

Features:

• Highly sensitive to solvent vapors and other VOCs. Bright green-yellow-red display clearly shows hazard level of gas or vapor.
• Detects down to OSHA, EPA, and other regulatory-mandated levels...typically at low ppm concentrations.
• Has built-in rechargeable battery for portable use in tracking leaks.
• Rugged construction with many safety features.